BS ISO 11451-2:2015 BSl Standards Publication Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 2: Off-vehicle radiation sources bsi. ..making excellence a habit. BS ISO 11451-2:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 11451-2:2015. The UK participation in its preparation was entrusted to Technical Committee AUE/16,Data Communication (Road Vehicles). A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @The British Standards Institution 2015.Published by BSI Standards Limited 2015 ISBN9780580785955 ICS 33.100.20; 43.040.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2015. Amendments issued since publication Date Text affected BS ISO 11451-2:2015 INTERNATIONAL ISO STANDARD 11451-2 Fourth edition 2015-06-01 Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 2: Off-vehicle radiation sources Vehicules routiers-Methodesd'essaid'un vehiculesoumis adesperturbationsélectriquesparrayonnementd'énergie électromagnetiqueenbandeétroite- Partie2:Sourcesderayonnementhorsduvehicule Reference number IS0 11451-2:2015(E) TSO @ISO2015 BSISO11451-2:2015 IS011451-2:2015(E) COPYRIGHTPROTECTEDDOCUMENT ISo 2015,Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic ormechanical, including photocopying,or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISo at the address below or ISo's member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org ii ISO2015-Allrightsreserved BSISO11451-2:2015 IS0 11451-2:2015(E) Contents Page Foreword ..iv 1 Scope ..1 2 Normative references 3 Termsanddefinitions 4 Test conditions 5 Test location 6 Test instrumentation .4 6.1 Field generating device. .4 6.2 Field probes. .5 6.3 Stimulation and monitoring of the device under test (DUT) 5 7 Test set-up .5 7.1 Vehicle placement. ..6 7.2 Field generating device location (relative to vehicle and shielded enclosure) .6 7.2.1 Antenna constraints .6 7.2.2 TLS constraints. 6 7.3 Vehicletest configurations .6 7.3.1 Vehicle not connectedto the powergrid .6 7.3.2 Vehicle in charging mode connected to thepower grid ..7 7.3.3 Vehicle in charging mode through wireless power transmission (WPT) .15 Testprocedure .17 8 8.1 Test plan. .18 8.2 .18 Test method 8.2.1 Field calibration. .18 8.3 Test report. 24 AnnexA(informative)Functionperformancestatusclassification .25 IS0 2015- All rights reserved ili BSISO11451-2:2015 IS0 11451-2:2015(E) Foreword Iso (the International Organization for Standardization) isa worldwide federation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out throughIsotechnical committees.Eachmemberbodyinterested inasubjectforwhichatechnical committee has been established has the right to be represented on that committee. International organizations,governmental and non-governmental, in liaison with Iso,also take part in the work. ISo collaboratescloselywiththeInternationalElectrotechnicalCommission(IEC)onallmattersof electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEc Directives, Part 1. In particular the different approval criteria needed for the diffe